Trinseo (NYSE: TSE), a global materials solutions provider and manufacturer of plastics, latex binders and synthetic rubber, conducted an expert presentation on
‘Safety for Food Contact Plastic Packaging” to participants interested in thermoformed and injection molded packaging value chain during the Quality & Safety Assurance and Testing Session of Thin Wall Packaging Asia 2017 in Singapore on September 19, 2017.
Libby Fong, Trinseo’s Product Stewardship Specialist, discussed foamed and non-foamed polystyrene (PS) resins used in common food contact applications. The main topics covered included:
“Polystyrene is widely accepted by various authorities and has been approved to be used in food contact applications by the Ministry of Health of the People’s Republic of China, the European Commission/European Food Safety Authority in Europe, the Indonesia National Agency of Drug and Food Control, the Japanese Ministry of Health, Labor and Welfare as well as the Food and Drug Administration in the United States,” said Fong. “There is abundant scientific evidence stating that styrene at typical exposure levels cause no long-term health problems.”
There are several things to consider when choosing the best packaging material. All packaging leaves an environmental footprint regardless of material type. It takes energy and raw materials to produce, transport, and recover or dispose of all materials. So it is important to measure all these impacts throughout the entire lifecycle of the product.
Styrene exists naturally in many foods & beverages. The amount of styrene that migrates from PS packaging is far below the acceptable standards for exposure. Replacing PS in food service by alternative materials would significantly increase waste.
Fong concluded that compared to other alternatives, plastic is a better material to use for food packaging. It is economical, can be used in hygienic applications, keeps food hot or cold, and can lead to less food waste.
Trinseo (NYSE:TSE) is a global materials solutions provider and manufacturer of plastics, latex binders, and synthetic rubber with a focus on delivering innovative, sustainable, and value-creating products that are intrinsic to our daily lives. Trinseo is dedicated to making a positive impact on society by partnering with like-minded stakeholders, and supporting the sustainability goals of our customers in a wide range of end-markets including automotive, consumer electronics, appliances, medical devices, packaging, footwear, carpet, paper and board, building and construction, and tires. Trinseo had approximately $3.0 billion in net sales in 2020, with 17 manufacturing sites around the world, and approximately 2,600 employees. For more information, please visit: www.trinseo.com.
Cautionary Note on Forward-Looking Statements
This press release may contain forward-looking statements including, without limitation, statements concerning plans, objectives, goals, projections, strategies, future events or performance, and underlying assumptions and other statements, which are not statements of historical facts or guarantees or assurances of future performance. Forward-looking statements may be identified by the use of words like "expect," "anticipate," "intend," "forecast," "outlook," "will," "may," "might," "see," "tend," "assume," "potential," "likely," "target," "plan," "contemplate," "seek," "attempt," "should," "could," "would" or expressions of similar meaning. Forward-looking statements reflect management’s evaluation of information currently available and are based on our current expectations and assumptions regarding the timing of the proposed acquisition of the Arkema MMA and PMMA business (the "Acquisition"); estimated and future results of operations, business strategies, competitive position, industry environment and potential growth opportunities and cost synergies relating to the Acquisition, our business, the economy and other future conditions. Because forward-looking statements relate to the future, they are subject to inherent uncertainties, risks and changes in circumstances that are difficult to predict. Factors that might cause such a difference include, but are not limited to, our failure to complete the Acquisition or meet the conditions to closing, including antitrust, works council and other regulatory approvals; the failure to obtain the financing necessary to fund the Acquisition and the impact of the substantial indebtedness to be incurred; costs related to the Acquisition; following the Acquisition, our ability to successfully integrate the acquired businesses, generate expected cost savings and synergies, maintain relationships with customers, retain key employees and profitably grow the business; and those factors discussed in our Annual Report on Form 10-K, under Part I, Item 1A —"Risk Factors" and elsewhere in our other reports, filings and furnishings made with the U.S. Securities and Exchange Commission from time to time. As a result of these or other factors, our actual results may differ materially from those contemplated by the forward-looking statements. Therefore, we caution you against relying on any of these forward-looking statements. The forward-looking statements included in this press release are made only as of the date hereof. We undertake no obligation to publicly update or revise any forward-looking statement as a result of new information, future events or otherwise, except as otherwise required by law.